News — Manual

Beginner's Guide: How to adjust VESC / Maytech SUPERFOC ESC FOC and BLDC? Setup FOC Wizard in VESCTOOL. Related products:  VESC based Controllers/Remotes This video will tell you how to set your VESC configuration in VESCTOOL?  Here we use below items as example to run the test: 1. Fully Waterproof Motor 65162 Inrunner Motor 2. Maytech New 200A 70V ESC MTSPF7.12K SUPERCASE200A V75 VESC_TOOL Compatible controller 3. Maytech MTSKR1905WF V2 New Waterproof Remote Control  Detection Steps:  1. Connect your VESC to computer and VESCTOOL 2. Setup Motors FOC in wizard, write in correct battery cells number according to battery you use, choose suitable motor type you...

The Transistoer switch can be used for LED Light System.  The Relay switch can be used for LED Light System or Water Pump Motor System.  Maytech MTSKR1905WF V2 New Waterproof Remote Control for Esk8/Esurf Maytech MTSKR20WFV2 V2 Remote for Esk8 1. Transistor Switch (MOSFET Switch) -Connect the SWI switch, your LED light and 3S battery as following shows.   -When (Short press Function button three times) transistor switch is on (display of 【2】in Screen Main interface), transistor switch source will be connected to GND and turn on LED. When it’s off(no display of【2】in Screen Main interface), LED is off. 2. Relay Switch...

Firstly, you need to prepare below tools to help:  1. Silicone cable that you need to use.  2. Heat shrink tube that is suitable for your cable.  3. Torx screwdriver. 4. Wire cutters to cut the rubber on silicone wires.  5. Terminal hydraulic pliers to crimp terminal connector. Steps: 1. Use torx screwdriver to unscrew the screws and terminal connector on switch.  2. Use wire cutters to cut about 5mm length rubber on silicone wires.  3. Connect the conductive end on the silicone cable to connetion port on terminal connector.  4. Use terminal hydraulic pliers to crimp terminal connector on silicone cable in...

1. Progcard Compatible ESC: MTSF300A-OPTO, MTSF300A-WP Attention Please: If you want to program on progcard, do not connect progcard to computer, otherwise it will use computer for programming, not on progcard. Progcard Port Definition: 2. Wiring Instruction: 2.1 MTSF300A-OPTO Splash waterproof Watercooled ESC ESC has two three pins cables. please do not mix , longer one is PWM throttle signal cable, short one is programmable cable, see below pictures: If use with Maytech MTSKR1905WF remote and DC-DC module (UBEC):  2.2 MTSF300A-WP Internal Receiver Fully waterproof ESC With built in receiver and DC-DC module(UBEC) About the external cables functions, please check MTSKR1905WF manual. 2.3 MTSF300A-WP external...

Function overview 1.1 The smallest VESC based controller on the market, with a size of only 18x65mm, can be used for miniaturized equipment, such as smart cars, micro robots, electric roller skates, drones, electric models, etc. 1.2 Based on powerful VESC software and hardware, it supports PWM analog voltage UART and USB speed signal input. It supports sensored and sensorless brushless motors and brushed motors, and supports square wave and FOC modes. 1.3 Support up to 10S lithium battery, over-current/over-temperature/over-voltage protection. 1.4 Support VESC_TOOL, UART is enabled by default in the factory firmware. It is recommended to connect VESC through the serial port of...