Efoil/Surfboard/Boat MTSF300A Waterproof ESC Wiring and Procard Wiring

Efoil/Surfboard/Boat MTSF300A Waterproof ESC Wiring and Procard Wiring

1. Progcard

Compatible ESC: MTSF300A-OPTO, MTSF300A-WP

Attention Please:

If you want to program on progcard, do not connect progcard to computer, otherwise it will use computer for programming, not on progcard.

Progcard Port Definition:

300A boat efoil surfboard ESC progcard

2. Wiring Instruction:

2.1 MTSF300A-OPTO Splash waterproof Watercooled ESC

ESC has two three pins cables. please do not mix , longer one is PWM throttle signal cable, short one is programmable cable, see below pictures:

Maytech 300A OPTO ESC with Water-cooling splash waterproof Aluminum Case Controller for Esurf/Efoil/Hydrofoil

If use with Maytech MTSKR1905WF remote and DC-DC module (UBEC): 

Maytech 300A OPTO ESC with Water-cooling splash waterproof Aluminum Case Controller for Esurf/Efoil/Hydrofoil

2.2 MTSF300A-WP Internal Receiver Fully waterproof ESC

With built in receiver and DC-DC module(UBEC)

Maytech 300A ESC 100% Waterproof Electric Speed Controller with Progcard for Eletric Surfboard Efoil Boat
Maytech 300A ESC 100% Waterproof Electric Speed Controller with Progcard for Eletric Surfboard Efoil Boat

About the external cables functions, please check MTSKR1905WF manual.

2.3 MTSF300A-WP external receiver Fully waterproof ESC

With built-in DC-DC module (UBEC)

Maytech 300A ESC 100% Waterproof Electric Speed Controller with Progcard for Eletric Surfboard Efoil Boat

If use with Maytech MTSKR1905WF remote: 

Maytech 300A ESC 100% Waterproof Electric Speed Controller with Progcard for Eletric Surfboard Efoil Boat

3. How to connect progcard on ESC and program?

You need to give extra 5V power to the programmable cable, otherwise progcard screen will not turn on.

When you give 5V power for the programmable cable, progcard screen will turn on, then you can start to program.

If the screen shows dark and no words showing, it might be the signal cable is plugged in mistake direction, take off the programmable cable and plug in opposite direction.

4. How to Program?

Defaults:  
Brake Type: Brake Off
Battery type: Lipo   
Cut Off voltage threshold: (3.0V/60%)
Motor timing: 2°
SBEC voltage output: 5.0V
Governor mode: RPM OFF
Start Up strength: 30%
Motor rotation: Forward
Low voltage cutoff type: Reduce Power.

4.1: Turn on the ESC power, pls make sure disconnect throttle (PWM signal), or you can’t program even if progcard is connected.

4.2: When program cable and 5V power are both connected, progcard screen will show “LCD Program Card”, press “MENU” button get into connection, and then screen will show “L Ready to Connect ESC”, progcard is trying to connect with ESC.

4.3: It takes about 10 seconds for progcard and ESC connection, if successfully connected, screen will display parameter items and values, press “MENU” to switch different parameter items, press “VALUE” to switch item values, press “RESET” to set all item values default, press “OK” to save current value.

4.4: If screen shows “L Ready to Connect ESC” for over 10 seconds, it means the connection is failed, you need to check if the ESC throttle (PWM signal) is disconnected or not, if confirmed throttle signal is disconnected, disconnect program cable, and reconnect progcard, if still not working, turn off ESC power, and redo the above steps.

4.5: After program, you need to turn off ESC and disconnect progcard, reconnect ESC power, then adjusted parameters can be effective.

5. Special Instruction:

All the 300A ESC Timing default value is 2 degree, progcard Timing default value is Auto.

If you press “RESET”, progcard will reset ESC Timing to Auto, this change is not problem for motor smaller than MTI65mm series, if motor is larger than MTI65 series, please must manually change ESC Timing back to 2 degree.

 

Voltar para o blogue

Deixe um comentário

Tenha em atenção que os comentários necessitam de ser aprovados antes de serem publicados.