How to use MTSF160A-WP32 160A Efoil ESC?  -- Manual

How to use MTSF160A-WP32 160A Efoil ESC? -- Manual

How to use MTSF160A-WP32 160A Efoil ESC? 

1. IP68 fully waterproof, can directly work in water.
2. Continuous current: 160A
3. Burst Current(at 10S):180A
4. Working Voltage: 6-14S Lipocells (Max 58.8V)
5. Net Weight:180g
6. Programmable cable(2-core):Green-RX,Yellow-TX
7. Signal cable(3-core):to connect receiver, eg. Maytech MTSKR1905WFreceiver
    • Wiring Instruction, signal and programmable cable

     

    MTSF160A-WP32 160A Efoil ESC progcard32 wiring diagram

    To connect MTSKR1905WF receiver:

    MTSF160A-WP32 160A Efoil ESC progcard32 wiring diagram
    • How to do ESC throttle calibration with Remote?

    Pleas Refer to Youtube Video:

     

    MTSF160A-WP32 160A Efoil ESC throttle calibration
    • Program settings via progcard32
    • Connect progcard: It needs to connect ESC to battery to power on progcard. (Battery votage needs to be 6S Lipo and above)
    MTSF160A-WP32 160A Efoil ESC
    • Program settings (the settings with Dash are Defaults):
    1. SMR Function: OFF/ON  
    This setting is no-use for electric watersports. Please keep it at “OFF”.
    2. Brake Type: OFF/ON   
    This setting is no-use for electric watersports. Please keep it at “OFF”.
    3. Motor Timing: Auto/5°/10°/15°/20°/25°/30°
    Please keep it at Auto.
    4. Motor Rotation: CW/CCW
    CW: motor default rotation direction
    CCW: Change the direction of motor rotation
    5. SR Function: OFF/ON
    This setting is no-use for electric watersports. Please keep it at “OFF”.
    6. Battery Cells: Auto/6S/8S/10S/12S/14S
    Auto: Calculate the number of battery cells based on 3.8V of a single battery cell
    Manual setting(6-14S): Manual setting according to different voltage ranges.
    7. LVC: OFF/3.0V/3.2V/3.4V/3.6V/NIMH60%
    Low voltage protection. For Example: Use a 4s Lipo battery and set it to 3.0V as the low voltage protection value. The low voltage protection value is: 3.0*4= 12.0V.
    8. Cutoff Type: Reduce Power/Hard Cutoff
    Reduce power: When the battery voltage reaches the preset low voltage protection value, the ESC reduces the output power to 70%;
    Hard Cutoff: When the battery voltage reaches the preset low voltage protection value, the ESC immediately shuts down the output power.
    9. BEC Voltage: 6V/7.4/8.4V
    This setting is no-use for electric watersports. Please keep it at “6.0V”.
    10. Acceleratation:Soft/Normal
    For Maytech Motors, please select “Soft”.
    11. Startup Power: Low/Mid/High
    For Maytech Motors, please select “Mid”.
    12. Restore Default
    To set all setttings to defaults.
    • Program process

    1. Turn on the ESC power, pls make sure ESC votlage is over 20V.

    2. Connect progcard

    MTSF160A-WP32 160A Efoil ESC progcard32

    3. Press “ITEM” and it will connect progcard to ESC

    MTSF160A-WP32 160A Efoil ESC progcard32

    4. Then you can press “Item” to change switch different setting items. And press△ and ▽ to check each item options. And press”OK” to set the parameters you want ( Option with * is the default setting).

    5. After programming, you need to turn off ESC and disconnect progcard, reconnect ESC power, then adjusted parameters can be effective.
     
    The users manual will be updated along with further product improvements. Pls contact us if any question when you use our products. You can reach us by email to support@michobby.com.

    Retour au blog

    Laisser un commentaire

    Veuillez noter que les commentaires doivent être approuvés avant d'être publiés.