Eco Kit - Efoil DIY Foil Assist Kit ( 6374 80KV Waterproof Motor +130A Fully Waterproof ESC + MTSKR26WF V5.0 Waterproof Remote )
Eco Kit - Efoil DIY Foil Assist Kit ( 6374 80KV Waterproof Motor +130A Fully Waterproof ESC + MTSKR26WF V5.0 Waterproof Remote )
SKU:MTO6374-80-WPC2+MTSF130A-WP32+Progcard-FP32+MTSKR26WF+MICP27FP
No se pudo cargar la disponibilidad de retiro
Have Doubts? Contact US!!
Have Doubts? Contact US!!
Because Shipping has regulation on Battery. If you order the kit including 8S3P or 10S3P battery, after you placing order, we will check and contact you to pay shipping cost for battery separately.
Or you can contact us by messenger or email (support@michobby.com) to check battery shipping cost and shipping time before order.
If you want to use other cheaper but slower shipping method, please contact support@maytech.cn. Shipping time by DHL or UPS is fast, normally 3-7 days arrive to you.
24-42V Efoil DIY Foil Assist Kit ( 6374 80KV Waterproof Motor +130A Fully Waterproof ESC + MTSKR26WF V5.0 Waterproof GPS Remote )
>>Check Test Data of 6374 80KV Motor with Plastic Propeller (Max 22KG Thrust) and Stainless Steel Propeller (Max 24.6KG Thrust)
Wiring diagram and parameters display on remote:
If you want to display RPM and battery power bar and voltage %, please follow:
1. Display battery bar and voltage %: Lead out a wire from your battery + to "BAT" on receiver
2. Display RPM: Lead out a wire from one of 2 motor wires, connect to "MOT" on receiver.
3. Setting in remote for this kit:
| Thr Mode: | Surfboard |
| Batt Type and Batt Ser Num | Please set according to your battery. |
| Data Source |
1. If you connected MOT for RPM display, then select 【Motor Wire】 2. If you don't connect MOT for ROM display, only need to display battery bat and voltage %, then select 【None】 |
| M.Pole Pairs | 7 |
| VESC Thr | None |
1. Fully Waterproof 6374 Motor with New Waterproof Treatment Technology on Rotor and Stator.
| Model No. |
MTO6374-80-WPC with 1m long wires (ceramic bearings) MTO6374-80-WPC2 with 1m long wires (stainless steel bearings) |
KV | 80, can be customized, contact us |
| Input Voltage | 3-10S Lipo (12.6-42V) | Idle Current | 0.8A |
| Max Output Watt | 3550W | Max Current | 65A |
| Shaft | φ8mm, No Output Shaft | Hall Sensor | Without |
| Mounting Hole Pattern | 28mm, 30mm, 44mm Hole distance | Mounting Hole Diameter | M4 |
| Customize | KV, logo, shaft, mounting hole pattern, color, connector, cable, etc., | Bearing | Ceramic Bearing or Stainless Steel Bearing |
| Application | Wing foil, wind surf foil, sup foil board, non-electric foil board, kite foil board, underwater thruster, underwater robot, ROV, etc., | ||
Our advanced waterproof technology:
Rotor magnets with anti-oxidation and anti-rust treatment;
Stator with insulation paint;
Coil Copper wires with transparent insulating varnish;
Wataerproof ceramic bearing or stainless steel bearing.
Some other waterproof motors stator and rotor are full filled with black glue. This kind of black glue may expand when motor heats up, it will expand, then distance between the stator and the rotor will be very small. If rotor and stator scraches each other , it will affect the life of the motor.
Moreover, if the rotor and stator are full filled with glue, the motor will heat up more easily and the motor power efficiency is poor.
Our waterproof 6374 motor insulating paint is harder than above normal black glue, and even if there is heat, it will not expand to affect the space between the stator and the rotor. It ensures longer motor life!
Difference between ceramic bearing and stainless steel bearing:
Stainless Steel Bearing:
1. Because seawater is corrosive, after some time use may get rust, need to wash with fresh water everytime after use, and keep the motor all dry, so to expand lifespan.
2. Can withstand higher speed.
3. Cost is less than cermic bearing.
Ceramic Bearing:
1. Better anti-rust performance, good for sea water condition
2. It’s brittle, can’t withstand very high speed, easier damage at high speed
3. cost is higher than stainless steel bearing.
2. Maytech New 32Bit 130A ESC Waterproof Speed Controller (Non-VESC)
| Model No | MTSKR26WF V5.0 |
| Upgraded Function | Equipped with GPS (GPS Speed, Distance, Max Speed, Average Speed) |
|
Equipped with Tilted protection (IMU tilt sensor), protection angle can be adjusted to 30°/45°/60° tilt degree of your board in case of flipping over, separation of the rider from the board, or an accidental fall. IMU degree can be calibrated according to the receiver position to be placed on your board. Tilt protection can be turned off for experienced users. |
|
| Waterproof Rank | IP68 Waterproof with 2 Layers Nanometers Coating, both on PCB board and screen |
| Thr Mode | Esurfboard (SF) , with cruise control and ESK8 (SK), can control forward and reverse when use on marine applications |
| 3 Speed Modes | With, adjust throttle % from 20-100%, friendly for beginners |
| Power Modes | 2 levels, Eco (Level 1) & Pro (Level 2) optional Signal strength: Pro ＞ ECO Power Consumption: PRO ＞ ECO |
| Throttle Lock | Yes, 10-120s optional |
| Signal Format | Support Standard PWM (PPM) and UART, output range from 10%-20%, which correspond to ESC/VESCTOOL Compatible controller throttle output range from 0%-100%. |
| PWM Signal Output Range | In Esk8 (SK) mode: 1.5ms is stop position, 1.5-1ms for brake or reverse (upper trigger), 1.5-2ms for throttle (bottom trigger) In Esurf (SF) mode: 1-2ms for throttle (bottom trigger), no brake or reverse |
| Double Source Power Supply | Accept 5V power by ESC built-in BEC or extra 5V power |
| Output Signal | Max 3.3V |
| Display Parameters |
GPS Speed / Distance / Max Speed / Average Speed Tilt sensor angle RPM+Current+Voltage+Temp(When work with VESC and MTSF-WP32 series ESCs) |
| Signal strength, remote and battery power bars, battery voltage%, RPM, speed (km/miles), with VESC, Maytech WP32 ESC and other ESCs | |
| Receiver built-in switch | 20V 2A Mosfet Switch (transistor switch); No Relay Switch for this version |
| Cruise Control | With in SF Mode (Esuf) |
| Brake or Reverse | With in SK Mode (Esk8) |
| Accessories | Wirelss charging pad / Receiver / USB cable / Wristband / 1pcs 3 pins cable / 1pcs UART cable |
| Compatible Controllers | VESC/ Focbox/ Other PWM ESCs that has same signal output range with the remote. |
| Application | foil assist system, electric propulsion, underwater thruster, electric outboard, Esurf, Efoil, electric hydrofoil, electric surfboard, electric skateboard/ elongboard/ mountainboard, electric paraglider, etc., |
4. Plastic or Metal Propeller
Material: Nylon Powder
Blade: 2 folding Blades
Color: Black
Mounting Holes: 8xM4
Max Rotation Diameter: 165mm/6.5'' (Approx.)
Height: 32mm/1.25'' (Approx.)
Propeller hub: Plastic
1 set includes 2 metal blades& 1pcs plastic hub. Propeller for MTO6374-WPC, MTO6384-WPC and MTO6579-WPC motors
Propeller hub: Plastic
1 set includes 2 metal blades& 1pcs plastic hub. Propeller for MTO6374-WPC, MTO6384-WPC and MTO6579-WPC motors
5. 8S3P battery or 10S3P battery with charger
(Each batch battery Lenth/Width/Height will have 1-3cm tolerance. Please subject to actual product you receive. Also each batch charger outlook may have some difference. Please note before order).
- MTLB8S3P lithium-ion 8S3P Battery Pack
with Molicel 21700 cells
Rated: 29.6V
Full charged: 33.6V
Capacity: 12.6Ah
with BMS
MTBC3305P Battery Charger
AC: 220V 50Hz
DC: 33.6V 5A
- MTLB10S3P lithium-ion 10S3P Battery Pack
with Molicel 21700 cells
Rated: 37V
Full charged: 42V
Capacity: 12.6Ah
with BMS
MTBC4250P Battery Charger
AC: 220V 50Hz
DC: 42V 5A
Recommended Related Parts:
Maytech Receiver Adapter UBEC Board 5V UBEC For MTSKR2005WF and MTSKR1905WF
2.4ghz extension antenna 1meter / 3meter for Maytech Remote Receiver
MICHOBBY Efoil 2-Blade Folding Propeller Plastic Or Stainless Steel Propeller
